Most homeowners know what to do when the power goes out: wait, check on the neighbors, reset the clocks. What almost nobody checks is whether their solar came back on, too.
Usually it does. Solar systems are built to shut off when the grid goes down and restart on their own a few minutes after power returns. But "usually" isn't "always." Sometimes part of a system restarts and part of it doesn't. The panels look the same from the street, the lights work, and the app may still show some production. The loss stays hidden until a bill, or a sharp-eyed homeowner, catches it.
A real case from Hastings-on-Hudson
This summer a Hastings-on-Hudson home lost power for about 40 hours over July 4–6. When the power came back, the solar array came back too, but only partly. Peak output dropped from about 5.5 kW to 1.6 kW. Nothing looked wrong from the ground, and the homeowners only found out weeks later, when we went through a year of their Con Edison meter data. By then it had been running that way for 55 days.
The system's older monitoring only showed totals, not individual panels, so there was no way to see what had stopped. We installed a new combiner panel and Enphase monitoring. With panel-level data, the problem was obvious: one whole string of panels wasn't producing. On the roof we found a burnt, shorted wire in the junction box. We replaced the wiring from the roof down to the combiner, and the whole system is producing again.
The lesson isn't that every outage breaks something. It's that a partial loss can hide for months if nobody compares the numbers.
Why solar shuts off when the grid goes down
Grid-tied solar is required to stop sending power to the lines during an outage, so utility crews working on them stay safe. When power comes back, the inverters wait, check that the grid is stable, and restart.
Most of the time that's seamless. But an outage, and especially the surges and flickers when power is restored, can trip a breaker, knock a gateway offline, or leave some equipment that needs a manual reset. If only part of the system restarts, you'll still see some production, which is exactly why it's easy to miss.
The 5-minute after-outage check
Do this the first sunny day after any outage that lasted more than a few minutes.
- Open your solar app around midday. Compare today's production with a similar sunny day before the outage. A drop of a third or more on a clear day is worth a closer look.
- Look for "not reporting" or "offline" alerts. If the whole app is blank, it may only be your internet. Our guide Solar monitoring says "offline": is your system actually down? walks through that.
- If your app shows per-panel data, check for gaps. A row or a group of panels showing zero while the rest produce points to one circuit or one piece of equipment that didn't restart.
- Check the breakers you can safely reach. Look at the solar breaker in your main panel and the outdoor AC disconnect, if you have one. Don't open covers that need tools. Our breaker checklist shows what to look for.
- Still low? Call us. Don't go on the roof and don't open the combiner box.
Catch it even if you never open the app
Con Edison customers with a smart meter can download up to a year of their own usage data through Green Button "Download My Data" in their online account (Account & Billing → Energy Use → Green Button). It comes as a spreadsheet.
You don't need to be a data expert. Compare the weeks before and after an outage. If your home suddenly started pulling noticeably more power from the grid on sunny afternoons and nothing else changed (no new heat pump, no guests, no EV), your solar may not be fully back.
Why this matters more in winter
Winter storms bring more outages, and shorter days make any production loss harder to spot. A system that's running at half power in December can look "normal" simply because December numbers are always low. That's why the comparison matters: check a clear day against a clear day, not against summer.
It also helps to keep a simple habit. After any outage, add a reminder to your phone for the next sunny day: "check solar." Two minutes in the app is enough. If you have a battery, check that it's back to its normal mode and charging, too. And if you've had work done on your electrical panel, a new generator hookup or a new router since your last check, mention it when you call. Those details often point straight to the cause.
When to call us
- Production is down a third or more on clear days after an outage.
- A group of panels shows zero.
- A breaker trips again after you reset it once. Leave it off and call.
- Anything is wet, scorched, smells like burning or buzzes. Stay away and call.
Rivertown Solar's in-house crew and licensed electricians service systems across Westchester and the Bronx, including systems we didn't install. Call (914) 231-6866 or send us a support request.
Related reading